Skip to main content

3pcs NRF51822 Beacon Module Bluetooth RSSI Positioning Module Geekcreit for Arduino - products that work with official Arduino boards

3pcs NRF51822 Beacon Module Bluetooth RSSI Positioning Module Geekcreit for Arduino - products that work with official Arduino boards
3pcs NRF51822 Beacon Module Bluetooth RSSI Positioning Module Geekcreit for Arduino - products that work with official Arduino boards3pcs NRF51822 Beacon Module Bluetooth RSSI Positioning Module Geekcreit for Arduino - products that work with official Arduino boards3pcs NRF51822 Beacon Module Bluetooth RSSI Positioning Module Geekcreit for Arduino - products that work with official Arduino boards


Get 3pcs NRF51822 Beacon Module Bluetooth RSSI Positioning Module Geekcreit for Arduino - products that work with official Arduino boards


Introduction and features:
 
1. Easy and fast customization of extremely low cost enclosures;
2. UUID, Major, Minor and other parameters can be changed according to customer needs;
3. Beacon barcode for easy identification;
4. Based on TI's NorDic51822/CR2032, low power Bluetooth module;
5. Support IOS7.0, Android 4.3 and above;
6. Receiving: 30M;
7. Battery life is 6 months to one year.
8. Working voltage: 1.8-3.6V

Test conditions: Ta = 25 ° C, VCC = 3.3V.
Technical indicatorsParameterRemarks
Operating VoltageDC 2V to 3.6V  
Working frequency2402~2480MHz  
Number of channels40  
ModulationGFSK  
Output Power-20dBm ~4 dBmProgrammable preparation
Emission current10.5mAPOWER is 0dBm, related to power
Receiving sensitivity-91dBmDirty transmitter mode
Receiving current13mA  
Stand-by current2.7uAStop broadcasting
Transmission rate1Mbps  
Chip flash256KB  
Chip RAM16KB  
Antenna formPCB antenna  
Communication distance>30m0dBm r
Storage temperature-40 ~ 125 ° C  
Operating temperature-20 ~ 75 ° C  
Dimensions24mm*4.5mm  

Note:

1 . The supply voltage of the module affects the transmit power. Within the operating voltage, the lower the voltage, the smaller the transmit power. Remarks:
2 . When the operating temperature of the module changes, the center frequency will change, as long as it does not exceed the operating temperature, it will not affect the application.
3 . The antenna has a great influence on the communication distance. Please install the module correctly.
4 . How the module is installed affects the communication distance.
 
Package includes:

3 x NRF51822 Beacon Module 















3pcs NRF51822 Beacon Module Bluetooth RSSI Positioning Module Geekcreit for Arduino - products that work with official Arduino boardsSee detail


Popular posts from this blog

DIY Qi Standard Wireless Charging Coil Receiver Module Circuit Board DIY Coil for Phone for Battery 5V 1A Fast Quick Charger

Get DIY Qi Standard Wireless Charging Coil Receiver Module Circuit Board DIY Coil for Phone for Battery 5V 1A Fast Quick Charger Features:   1. Pure copper coil, high permeabillity, low loss, assuring fast charging. 2. Can charge the battery directly. 3. Charging current is around 5V 1A. 4. Can be directly connected to the phone's motherboard, the phone will display wireless charging. 5. Red is positive and gold is negative. The wire can be bent freely.   Specification:   Material: PCB Product Name: Wireless Charger Receiver Module Input Power: 5V 1A or 9V 0.5A Output: Power up to 5W Charging Efficiency: 75% Transmission distance: 2-8mm Charger Applicable Form: Wireless Charger Executive Standard: Qi Wireless Charging Standard Product Certification: CE/FCC/ROSH Board Size: 1.9 * 3.2cm / 0.7 * 1.3in Copper Coil Size: 4.1 * 2.9cm / 1.6 * 1.4in Cable Length: 5cm / 2.0in Weight: approx. 6g   Note:   Wireless charging = transmitter + receiver (both can be charged together) 1, there...
Read more

24-bit PCM5102 PCM5102A Stereo DAC Digital-to-analog Converter PLL Voice Module pHAT

Buy 24-bit PCM5102 PCM5102A Stereo DAC Digital-to-analog Converter PLL Voice Module pHAT Instruction: If music is the food of love, play on. But make sure you use this super little DAC Module to get the best out of your Raspberry audio! The DAC Module provides a super affordable high-quality DAC for the Raspberry. Pumping out 24-bits at 192KHz of audio goodness from the Raspberry's I2S interface on the 2x20 pin GPIO header. Since it's digital audio, it sounds really good, much better than the onboard analog audio. The 3.5mm stereo jack comes soldered onto the board already. Features: 24-bit audio at 192KHz Line out stereo jack pHAT format board Uses the PCM5102A DAC to work with the Raspberry I2S interface Package includes: 1 x DAC digital to analog converter 24-bit PCM5102 PCM5102A Stereo DAC Digital-to-analog Converter PLL Voice Module pHAT Buy Now
Read more

433MHz 12V 4CH Channel Relay RF Wireless Remote Control Switch 2 Transmitter+Receiver

Get 433MHz 12V 4CH Channel Relay RF Wireless Remote Control Switch 2 Transmitter+Receiver Feature:   Remote Control Distance: 100 meter(open/ideal) in theory, 10%-50% in reality(In open environment) Encode: Fixed code, soldering Frequency: 433mHZ Channel: 4 CH Power Supply: DC 12V Relay: DC 12V Quiescent Current: 8mA Work Voltage Range of Relay: AC 110-240V or DC 0-28V Sensitivity:-105 dBm Operating Temperature: -40℃~80℃ Receiver Size: 68x47x17mm   Control Mode:   1. Toggle/Self-Lock: Press->On; Press again->Off press one button for one time is working/ON .press the same button again is stop/OFF . (1 channel switch(receiver) need 1 button remote control (transmitter). 2. Latched/Inter-Lock: Press->On; Press other button->Off press one button is working/ON ,press another button is stop/OFF . ( 1 channel switch( receiver) need 2 buttons remote control (transmitter). 3. Momentary/Jog: Press and hold->On; Release->Off Keep pressing one button is working /ON. loosen you...
Read more