433MHz 12V 4CH Channel Relay RF Wireless Remote Control Switch 2 Transmitter+Receiver

Get 433MHz 12V 4CH Channel Relay RF Wireless Remote Control Switch 2 Transmitter+Receiver

Feature:

Remote Control Distance: 100 meter(open/ideal) in theory, 10%-50% in reality(In open environment)

Encode: Fixed code, soldering

Frequency: 433mHZ

Channel: 4 CH

Power Supply: DC 12V

Relay: DC 12V

Quiescent Current: 8mA

Work Voltage Range of Relay: AC 110-240V or DC 0-28V

Sensitivity:-105 dBm

Operating Temperature: -40℃~80℃

Receiver Size: 68x47x17mm

Control Mode:

1. Toggle/Self-Lock: Press->On; Press again->Off

press one button for one time is working/ON .press the same button again is stop/OFF . (1 channel switch(receiver) need 1 button remote control (transmitter).

2. Latched/Inter-Lock: Press->On; Press other button->Off

press one button is working/ON ,press another button is stop/OFF . ( 1 channel switch( receiver) need 2 buttons remote control (transmitter).

3. Momentary/Jog: Press and hold->On; Release->Off

Keep pressing one button is working /ON. loosen your finger is stop/OFF . 1 channel switch(receiver) need 1 button remote control (transmitter )

Learn code and Remove Code:

1. Learn: Press the learning code . The indicator from 'on' to 'off' , loosen your finger, press any button of the remote control ,the indicator flash 2 times and off .it mean you learn it successfully .it can learn more than 12 PCS 2260/2262 chip with the different code wireless remote control.

2. Remove: Press the learning button about 8 seconds , the indicator turn on to off , it means the Code had been removed successfully.

Package Includes:

1 x Receiver

2 x Transmitter (Battery include)

433MHz 12V 4CH Channel Relay RF Wireless Remote Control Switch 2 Transmitter+ReceiverSee detail

DIY Qi Standard Wireless Charging Coil Receiver Module Circuit Board DIY Coil for Phone for Battery 5V 1A Fast Quick Charger

Get DIY Qi Standard Wireless Charging Coil Receiver Module Circuit Board DIY Coil for Phone for Battery 5V 1A Fast Quick Charger Features: 1. Pure copper coil, high permeabillity, low loss, assuring fast charging. 2. Can charge the battery directly. 3. Charging current is around 5V 1A. 4. Can be directly connected to the phone's motherboard, the phone will display wireless charging. 5. Red is positive and gold is negative. The wire can be bent freely. Specification: Material: PCB Product Name: Wireless Charger Receiver Module Input Power: 5V 1A or 9V 0.5A Output: Power up to 5W Charging Efficiency: 75% Transmission distance: 2-8mm Charger Applicable Form: Wireless Charger Executive Standard: Qi Wireless Charging Standard Product Certification: CE/FCC/ROSH Board Size: 1.9 * 3.2cm / 0.7 * 1.3in Copper Coil Size: 4.1 * 2.9cm / 1.6 * 1.4in Cable Length: 5cm / 2.0in Weight: approx. 6g Note: Wireless charging = transmitter + receiver (both can be charged together) 1, there

10pcs 4 Digit 7-Segment 0.56' LED Display Tube Decimal 7 Segments HT16K33 I2C Clock Double Dots Module For Arduino

Get 10pcs 4 Digit 7-Segment 0.56' LED Display Tube Decimal 7 Segments HT16K33 I2C Clock Double Dots Module For Arduino >>>Manual: Click here to open<<< Features: - These 7-segment displays normally require 13 pins (5 characters and 8 total segments each). - Solves the annoyance of using 13 pins or a bunch of chips by having an I2C constant-current matrix controller sit neatly on the back of the PCB. - The controller chip takes care of everything, drawing all the LEDs in the background. - All you have to do is write data to it using the 2-pin I2C interface. - There are three address select pins so you can select one of 8 addresses to control up to 8 of these on a single 2-pin I2C bus (as well as whatever other I2C chips or sensors you like). - The driver chip can din the entire display from 1/16 brightness up to full brightness in 1/16th steps. - It can't din individual LEDs, only the entire display at once. - Size: 5.03 x 2.68 x 1.2 cm/2 x 1.1 x 0.5 inch

8/10/12 Inch Ultralight Carbon Fiber Floating Lamp Magic Arm Underwater Photograph Diving Accessories

Get 8/10/12 Inch Ultralight Carbon Fiber Floating Lamp Magic Arm Underwater Photograph Diving Accessories Specification: Type:Underwater Photography floating arm Size: 8 10 12 inch Color: black Material : carbon fiber Package included: 1 x Underwater Photography Floating Arm 8/10/12 Inch Ultralight Carbon Fiber Floating Lamp Magic Arm Underwater Photograph Diving Accessories See detail

Anwen Tanner

Search This Blog